mecㆍviewer v1.4 :: RFP_High Level Induced Transient Susceptibility Test Set.pdf

KARI PROPRIETARY

Request For Proposal

High Level Induced Transient Susceptibility

Test-Set for Spacecraft EMC Test Equipment

March 25, 2020

Space Test Department

Korea Aerospace Research Institute

169-84 Gwahangno, Yuseung, Daejeon, 34133, KOREA

Phone : 82(42)860-2977, Fax : 82(42)860-2234

KARI PROPRIETARY

Request For Proposal

for

High Level Induced Transient Susceptibility

Test-Set for Spacecraft EMC Test Equipment

IMPORTANT

1. This RFP should be kept in confidentiality and should neither
be copied nor distributed to the third parties.
2. The questions and opinions on this RFP can be asked or
suggested to Korea Aerospace Research Institute before
submission of the proposal.
3. This RFP should be returned to Korea Aerospace Research
Institute with bidder’s proposal.
4. This RFP shall be legal bind after the contract is awarded
unless the bidder explicitly expresses the differences from the
RFP in the compliance sheet.

March 25, 2020

Space Test Department

Korea Aerospace Research Institute

169-84 GWAHANGNO,

YUSEONG

DAEJEON, 34133, KOREA

Phone : 82(42)860-2977, FAX : 82(42)860-2234

e-mail : jjw0302@kari.re.kr

RFP.SITC.KARI.KOREA

2020.03.25

Space Environment Test Division.

PART I. Overview

Overview of the project

1.1. Korea Aerospace Research Institute (hereinafter referred to as “KARI”)

is located at Daeduk Research Complex, 140 km south of Seoul.

1.2. KARI has a satellite assembly, integration and test center (hereinafter

referred to as “AITC”) for joint use by corporations and research

institutes for the purpose of the effective development of domestic

satellites. And basic facilities and equipment for satellite assembly

and test have been supplied, installed and used.

1.3. The purpose of this project is to install waveform generators set

including generators, system accessories, controller and software etc.

to perform all test items defined in DO-160G section 22(detailed

requirements are defined PART II) and MIL-STD-461G CS117. These

equipments will be installed in KARI EMC chamber.

1.4. The main undertakings of the project are to perform factory and site

acceptance tests, install, guarantee quality and training, etc.

1.5. The supplier should submit the business showings of the installing

the Test Equipment for Induced Transient Susceptibility.

1.6. All the descriptions in this RFP are minimum requirements and the

supplier can suggest the better one to improve the overal

performance and cost. But in this case, the proposal should clearly

indicate the improvements from KARI’s requirements.

RFP.SITC.KARI.KOREA

2020.03.25

Space Environment Test Division.

Procedures of the project

2.1. The project shall be proceeded with five parts as follows:

2.1.1. Organization of waveform generator set including system

accessories, controller and software etc.

2.1.2. Factory acceptance test & safety plan verification

2.1.3. Transportation

2.1.4. Installation at KARI

2.1.5. Final acceptance test at KARI according to supplied test

procedure & previous test results

2.2. The participants shall submit the detailed work schedule for article

2.2.1. Specially, the work schedule at KARI shall be confirmed by KARI

for avoiding overlap with KARI’s other test schedules.

2.3. The format of proposal

2.3.1. The participants shall submit 6 copies of a detailed proposal to

KARI according to the format and contents satisfying the

requirements stipulated in this RFP.

2.3.2. The compliance sheet with the requirement of this RFP shall

certainly be included in the proposal.

2.3.3. The price of the system shall be broken down.

2.3.4. The participants shal make out a proposal with their own writing.

2.3.5. The language shall be English or Korean.

2.4. The proposal shall be delivered to KARI before the due date for

submission.

RFP.SITC.KARI.KOREA

2020.03.25

Space Environment Test Division.

2.5. All proposals and documents submitted shall become the property of

KARI.

Requisites of participants

3.1. The participants shall supply information about themselves.

3.2. The participants shall have experience of installation, operation,

arranging, integration of waveform generators set for lightning

induced transient susceptibility test to be installed in EMC test facility

in Korea.

Scope of the contract

4.1. The project is on turnkey base and the proposal shall include the

following;

4.1.1. Engineering work of the equipment

4.1.2. Manufacture, assembly and turnkey delivery of the equipment

4.1.3. Parts and particular instruments necessary to operate the

equipment

4.1.4. Installation work and acceptance test at factory & KARI site

4.1.5. Project management, site operation, cooperation with KARI

4.1.6. Basic principle, operation, warranty, maintenance, repair, safety

and training for the equipment

4.1.7. Relevant books and manuals

RFP.SITC.KARI.KOREA

2020.03.25

Space Environment Test Division.

4.1.8. Other necessary matters required for acquiring and installing the

equipment (including checking of AITC building interface and

construction)

RFP.SITC.KARI.KOREA

2020.03.25

Space Environment Test Division.

PART II. TECHNICAL REQUIREMENTS

I. General

Waveform generators set for induced transient susceptibility test will be

installed in EMC chamber in KARI.

This system is for Induced Transient Susceptibility test defined in RTCA DO-

160G Section 22 and MIL-STD-461G CS117. This test system shall be designed

and almost complied in accordance with RTCA DO-160G Section 22.0 and MIL-

STD-461G CS117.

II. Configuration of Goods

Generator : 1 set

System Accessories : 1 set

2.1. AUX Connector(for safety circuit)

2.2. Test Cables(for EUT Connection)

2.3. User manual, conformity declaration and verification protocol

System Controller and Software(Demo Disks GENECS and TEMA) : 1 set

III. DETAIL SPECIFICATION

RFP.SITC.KARI.KOREA

2020.03.25

Space Environment Test Division.

Following waveforms shall be generated by transient generator. Test level

is defiend in 5. Acceptance Test and DO-160G Section 22.

1.1. WF1 [WaveForm(hereinafter referred to as “WF”)]

- Rise Time: 6.4 μs (± 20 %)

- Half value time: 69 μs (± 20 %)

- Generator Setting Range: 20 A ~ 1800 A or wider

- Generated level with Coupler: 20 A ~ 3180 A or wider

1.2. WF4

- Rise Time: 6.4 μs (± 20 %)

- Half value time: 69 μs (± 20 %)

- Generator output: 70 V ~ 1700 V / 340A for Pin/Ground Injection

- Generated output with Coupler: FS 300~750 V SS 75 V~187.5 V

or higher for cable induction test

1.3. WF5A

- Rise Time: 40 μs (± 20%)

- Half value time: 120 μs (± 20%)

RFP.SITC.KARI.KOREA

2020.03.25

Space Environment Test Division.

- Generator Setting Range: 80A ~ 3000A or Wider

- Generated level with Coupler: 80A ~ 10000A or Wider

1.4. Waveform definition

Waveform 1(Current)

Waveform 4(Voltage)

Configur
ation

Waveform 5(Current/Voltage)

Configur
ation

System Composition

2.1. Waveform Generator

2.2. AUX Connector(for safety circuit)

2.3. Test Cables(for EUT Connection)

2.4. User manual, conformity declaration and verification protocol

RFP.SITC.KARI.KOREA

2020.03.25

Space Environment Test Division.

2.5. System Controller and Software(Demo Disks GENECS and TEMA)

Environment condition

3.1. Temperature condition

3.1.1. Ambient temperature : 0℃ ~ 45℃

3.1.2. Storage temperature: -20˚C ~ +85˚C

3.2. Relative humidity : up to 95%

3.3. Location : normal laboratory environment

3.4. Operating altitude : up to 2000m above sea level

Acceptance Test

Fol owing acceptance tests shal be performed for al delivered test

systems.

4.1. Acceptance test procedure

4.1.1. Unpacking

4.1.2. Visual inspection

4.1.3. Installation of the Test systems in EMC chamber

4.1.4. Electricity connection

4.1.5. Oscilloscope, RF cables, probes, couplers, load and system

accessaries connection fitted for each test item.

4.1.6. System control line connection

RFP.SITC.KARI.KOREA

2020.03.25

Space Environment Test Division.

4.1.7. Fill acceptance test results in the performance test report

4.2. Acceptance test items, level and methods

For all test items, CI is Cable Injection, GI is Ground Injection, SS is

Single Stroke and L is Level, respectively.

Detailed test specification and methods are defined in RTCA DO-

160G Section 22 and MIL-STD-461G CS117.

4.2.1. Waveform 1

Type

Injection

Event

Level 4

Level 5

Cable

Bundle

Yes

4.2.2. Waveform 4

Type

Injection

Event

Direct

Yes

Cable

Bundle

Yes

4.2.3. Waveform 5A

Type

Injection

Event

Direct

Yes

RFP.SITC.KARI.KOREA

2020.03.25

Space Environment Test Division.

Cable

Bundle

Yes

4.3. If needed by request of a purchaser, Factory Acceptance Test shall

be performed in the place of production.

Remarks

5.1. Payment condition : 90% release Goods is ready to ship, 10% release

installation and training is done.

5.2. Warranty must be guaranteed for at least 12 months.

5.3. The delivery should be within 6 months after receipt of PO.

5.4. Software and Rack etc must be provided by the supplier. This would

be discussed between both parties.

5.5. Training and verification on delivery of goods should be provided

with more than 2 weeks by wel experienced engineer who has dealt

with more than two system for more than five years.

5.6. All generator should be powered by Single Phase 220V, 16A.

5.7. Test system has an ability to test at least two EUTs simultaneously in

parallel.

5.8. Test System does never be al owed to include any ROHS Material to

harm user’s health.

5.9. Supplier should provide end-user with calibration/verification data

of delivery of goods. It includes WF1/WF4/WF5A and al possible test

level.

RFP.SITC.KARI.KOREA

2020.03.25

Space Environment Test Division.

Appendix. Verification Setup For Acceptance Test

1. Pin Injection Calibration Setup, Signal Pins & Power Pins Direct Injection

Method

2. Typical Generator Performance Verification Setup for Cable Induction

Tests

RFP.SITC.KARI.KOREA

2020.03.25

Space Environment Test Division.

3. Typical Generator Performance Verification Setup for Ground Injection

Tests